4Bros AR-15 Rifle Wall Hanger

AR-15 Rifle Wall Hanger – Horizontal Magwell Mount

This 3D-printed AR-15 Rifle Wall Hanger provides a secure, cost-effective, and space-efficient way to store your rifle horizontally on a standard 2" x 4" framed wall. Designed specifically for AR-15 rifles with mil-spec dimension lower receivers, the hanger mounts directly into a wall stud using three included cabinet screws for strength and long-term reliability.

Secure Magwell Locking Design

The rifle interfaces with the hanger through the magwell and locks into place using the magazine release button. To remove the rifle, simply depress the magazine release and lift the firearm upward and off the mount. This intuitive retention method keeps the rifle firmly secured while allowing fast, controlled removal when needed.

Stud-Mounted Strength You Can Trust

Unlike many wall-mounted rifle hangers that rely on offset or staggered fasteners, this design features a linear screw pattern. All three mounting screws align directly with a single wall stud, maximizing load distribution and structural integrity. The hanger depth is engineered so that most rifles can be removed without contacting the wall surface.

Durable PETG Construction

The wall hanger is manufactured from PETG, a polymer selected for its excellent balance of strength, flexibility, and impact resistance. PETG is less brittle than many common plastics, reducing the risk of chipping or cracking while still providing the rigidity required to support a loaded AR-15 rifle.

Included Hardware and Installation Template

Each wall hanger ships with all required mounting hardware for installation through 1/2" drywall into a standard 2 x 4 stud. A drill template is also included to ensure proper hole spacing and alignment. You will need a 3/32" drill bit for pilot holes and an extended T15 bit to drive the screws.

Installation Instructions

1. Select a mounting location with sufficient clearance for your rifle. Test-fit the hanger in the rifle before drilling.
2. Locate the wall stud using a stud finder and mark both edges with a pencil.
3. Center and level the included drill template over the stud. Secure it with painter’s tape if needed.
4. Drill three pilot holes approximately 2" deep using a 3/32" drill bit.
5. Install the center screw first and snug it lightly without fully tightening.
6. Level the hanger using a small level placed on top.
7. Start the top and bottom screws without tightening fully.
8. Recheck level alignment.
9. Tighten the center screw while maintaining level, then fully tighten the top and bottom screws.

Do not overtighten the screws. The mounting hardware is stronger than the polymer, and excessive torque may damage the hanger.

Load Testing Results

To evaluate strength, the hanger was mounted to a 2" x 4" using the included screws and loaded with incremental weight. Initial testing reached 125 pounds with ease. Additional testing showed failure occurring between an estimated 225–250 pounds, demonstrating a substantial safety margin for typical AR-15 rifles.

Important Notes

• Designed for mil-spec AR-15 lower receivers; some aftermarket or billet lowers may fit, but compatibility is not guaranteed.
• This is a 3D-printed product and may show minor cosmetic imperfections that do not affect function.
• Availability is limited, and items are not offered for backorder.

Related Accessories

Browse additional accessories, tools, and gear here: 4BROS Accessories

Frequently Asked Questions

Will this wall hanger work with all AR-15 rifles?

The hanger is designed for AR-15 rifles with mil-spec dimension lower receivers. Most standard lowers will fit, but some billet or non-standard lowers may not.

How much weight can the wall hanger support?

Testing indicates failure occurs between approximately 225 and 250 pounds when properly mounted into a wall stud, providing a wide safety margin for normal use.

Does the rifle touch the wall when mounted?

No. The hanger depth allows most rifles to be removed and stored without contacting the wall surface.

Is mounting hardware included?

Yes. All required screws and a drill template are included for mounting into a standard stud behind 1/2" drywall.

 

Photos of our scientific testing procedure

 

Please review our Four Brothers Holsters Exchange, Return and Refund Policy

Made in America. Founded, located, engineered, manufactured, and shipped from Northern Indiana.